User manual
Dishwasher
DX 301
• A qualified and competent person must do the
plumbing installation.
Contact your local Customer Care Centre.
• Do not drill into the sides of the appliance otherwise
damage to hydraulic and electrical components may
occur.
• Do not change the specifications or modify this prod-
uct. Risk of injury and damage to the appliance.
• Do not use the appliance:
Warning! Carefully obey the instructions for
electrical and water connections.
– if the mains cable or water hoses are damaged,
– if the control panel, worktop or plinth area are
damaged so that you can get access to the inner
side of the appliance.
3
Control panel
1 On/off button
2 Button Lock
3 Program selection buttons
4 Delay start button
5 Indicator lights
6 Digital display
Indicator lights
The indicator light comes on when the washing phase
Washing
Drying
or the rinsing phase operates.
The indicator light comes on when the drying phase
operates.
Finished
Rinse Aid
The indicator light comes on when the washing pro-
gram is completed.
The indicator light comes on when it is necessary to fill
the rinse aid container. Refer to 'Use of rinse aid'.
The indicator light is off while a washing program op-
erates.
Button Lock
Comes on when the Button Lock function is active.
Button Lock
TheButtonLockfunctionlocksall buttonsonthecontrol
panel while the washing program is in operation.
The Button Lock function can be set only after a
washing programme starts. It is not possible to
set this function with the delay start.
4
Follow these steps to set the Button Lock function:
1. Switch on the appliance.
Digital display
The display shows:
2. Set a washing program.
• program duration,
3. Start the washing program.
• remaining time to the end of the program,
• end of a washing program,
• number of hours in delay start,
• fault codes,
4. Press Button Lock for approximately 5 seconds, or
until the Button Lock indicator light flashes.
5. Button Lock indicator light flashes for approximate-
ly 15 seconds.
• Button Lock function. The digital display shows CL
when this function is active.
6. When Button Lock function is active the indicator
light is on with a static light.
If you press a button while Button Lock function is on,
the digital display shows CL to inform you that the but-
tons are locked.
Setting mode
The appliance is in setting mode when all the program
indicator lights are on.
The appliance must be in setting mode to set a washing
program.
If a program indicator light is on, cancel the program to
go back to the setting mode. Refer to 'Select and start
a washing program'.
At the end of a washing program the Button Lock func-
tion is deactivated by opening and closing the door or
switching off the appliance.
Important! It is not possible to deactivate the Button
Lock function while a washing program is in progress.
To do this you must cancel the set program. Refer to
'Select and start a washing program'.
Delay start button
Use the delay start button to delay the start of the
washing program with an interval between 1 and 19
hours. Refer to 'Select and start a washing program'.
5
Washing programs
Washing programs
Program
Degree of soil
Heavy soil
Type of load
Program description
Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Pots
Crockery, cutlery,
pots and pans
Drying
1)
Any
Crockery, cutlery,
pots and pans
Prewash
Auto
Main wash up to 50°C or 65°C
1 or 2 intermediate rinses
Final rinse
Drying
2)
Normal or light soil
Normal soil
Crockery and cutlery Main wash up to 60°C
(Partial load) Final rinse
Quick 30
3)
Crockery and cutlery Prewash
Main wash up to 50°C
Regular Eco
1 intermediate rinse
Final rinse
Drying
Rinse & Hold
Any
Partial load (to be
1 cold rinse (to prevent food
completed later in the scraps to bond).
day). Detergent is not necessary with
this program.
1) During the Auto program, the soil level of the dishes is given by how cloudy the water is. The program duration and
consumptions can change. This depends if the appliance is fully or not and on the level of soil on the dishes. The appliance
adjusts automatically the temperature of the water during the main wash.
2) This is the perfect daily program to clean a partial load. Ideal for a family of 4 persons who only want to load breakfast and
dinner crockery and cutlery.
3) Test program for test institutes. Please refer to separate leaflet supplied, for test data.
Consumption values
1)
Energy (in kWh)
Water (in litres)
Program
Pots
1,8 - 2,0
1,1 - 1,8
0,9
12 - 25
12 - 25
9
Auto
Quick 30
Regular Eco
Rinse & Hold
0,8 - 0,88
0,1
11 - 12
4
1) The display shows the program duration.
6
The pressure and temperature of the water, the
variations of power supply and the quantity of
dishes can change these values.
Use of the appliance
4. Fill the detergent dispenser with the correct quan-
tity of detergent.
Refer to specified instructions for each step of the pro-
cedure.
5. Start the washing program.
1. Fill the rinse aid dispenser with rinse aid.
2. Load cutlery and dishes into the dishwasher.
3. Set the correct washing program for the type of
load and soil.
Use of rinse aid
Caution! Only use rinse aid specified for
dishwashers.
Caution! Do not fill the rinse aid dispenser with
other products (e.g. dishwasher cleaning agent,
liquid detergent). There can cause damage to the
appliance.
Follow these steps to fill the rinse aid dispenser:
Adjusting the rinse aid dosage
The rinse aid is set at the
factory at position 3.
To increase or decrease
the dosage refer to 'What
to do if...'
1
3
2
4
Wash hands to remove any residue of rinse aid
from skin.
Loading cutlery and dishes
• Before you load cutlery and dishes, do these steps:
– Remove all food remainings and debris.
– Make burnt, remaining food in pans soft.
Helpful hints and tips
Caution! Only use the appliance for household
utensils that are suitable for dishwashers.
Do not use the appliance to clean objects that can ab-
sorb water (sponges, household cloths, etc.).
7
• While you load cutlery and dishes, do these steps:
– Load hollow items (e.g. cups, glasses and pans)
with the opening down.
– Make sure that water does not collect in the con-
tainer or in a deep base.
– Make sure that cutlery and dishes do not lie inside
one another.
– Make sure that cutlery and dishes do not cover
other cutlery and dishes.
3
The rows of prongs in the
lower basket can be ad-
justed flat to load pots,
pans and bowls.
– Make sure that glasses do not touch other
glasses.
– Put small objects in the cutlery basket.
• Plastic items and pans with non-stick coatings can
retain water droplets. Plastic items do not dry as well
as porcelain and steel items.
• Put light items in the upper basket. Make sure that
the items do not move.
Caution! Make sure that the spray arms can
move freely before you start a washing program.
Warning! Always close the door after you load
or unload the appliance. An open door can be
dangerous.
1
2
Use the cutlery grid for best washing results. If the di-
mensions of the cutlery prevent use of the cutlery grid,
remove it.
1
2
Arrange service dishes
and large lids around the
edge of the lower basket.
1
2
Arrange the items to let
water touch all surfaces.
For longer items, fold the
cup racks up.
Prevent to put plates in the first three sectors in
the front part of the basket. Make sure the plates
tilt forward.
Adjustment of the height of the upper basket
If you put large plates in the lower basket, first move
the upper basket to a upper position.
8
Follow these steps to move the upper basket to the
lower position:
Maximum height of the dishes
upper basket lower basket
1. Pull the basket out until it stops.
Upper position 20 cm
Lower position 24 cm
31 cm
27 cm
2. Carefully lift the two sides upwards.
3. Hold the mechanism and guide it back down slow-
ly.
Follow these steps to move the upper basket to the
upper position:
Caution!
• Do not lift or lower the basket on one side only.
1. Pull the basket out until it stops.
• If the basket is in the upper position, do not put cups
on the cup racks.
2. Carefully lift the two sides until the mechanism is
engaged and the basket is stable.
Use of detergent
Only use detergents (powder, liquid or tablet) that
are suitable for dishwashers.
Follow the data on the packaging:
• dosage recommended by the manufacturer,
• storage recommendations.
Do not use more than the correct quantity of de-
tergent to decrease pollution.
3
4
Fill the detergent dis-
penser (A) with deter-
gent.
If you use a washing pro-
gram with prewash
phase, put more deter-
gent in the prewash de-
tergent compartment (B).
1
2
9
Refer to the instructions from the manufacturer for the
use of these products.
With tablets that contain rinse aid:
• set the lowest position for the rinse aid dosage,
• do not put rinse aid in the rinse aid dispenser. In this
condition rinse aid indicator light is always on when
you switch on the appliance.
.
Do these steps if the drying results are not satis-
factory:
5
6
1. Fill the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
Different brands of detergent dissolve in different
times. Some detergent tablets do not have the
best cleaning results during short washing programs.
Use long washing programs when you use detergent
tablets to fully remove the detergent.
If you go back to use normal detergents again, fill
the rinse aid dispenser and adjust the rinse aid
dosage.
Use of combi detergent tablets
These products are detergents with a combined clean-
ing and rinsing functions. They can contain also other
cleaning agents.
10
Select and start a washing program
Cancelling delay start
Set the washing program with the door ajar. The
washing program only starts after you close the
door. Until then it is possible to modify the settings.
1. Press and hold, approximately for 3 seconds, the
two buttons above the word Cancel until all the
program lights come on.
1. Press the on/off button.
– When you cancel delay start, you also cancel
the washing program.
2. Make sure that the appliance is in setting mode.
3. Press one of the program buttons. Refer to the
'Washing programs' chart for program details.
2. Set a new washing program.
Warning! Only interrupt or cancel a washing
program if necessary.
Attention! Open the door carefully. Hot steam and
water can escape.
– The program indicator light comes on.
– The Washing indicator light comes on.
– The flashing digital display shows the program
duration.
4. Close the door.
Interrupting a washing program
– The washing program starts automatically.
Open the door.
– The program indicator light and the Washing in-
dicator light stay on.
• The program stops.
Close the door.
• The programcontinuesfromthepointofinterruption.
When the washing program operates, you cannot
change the program. Cancel the washing pro-
gram. Refer to 'Cancelling a washing program'.
Cancelling a washing program
1. Press and hold, approximately for 3 seconds, the
two buttons above the word Cancel until all the
program lights come on.
Select and start a washing program with delay
start
1. Press the on/off button.
2. Set a washing program.
2. Release the two buttons, the washing program has
been cancelled.
At this point, you can follow these steps:
3. Press the delay start button until the display shows
the necessary delay start of the washing program.
1. Switch off the appliance.
2. set a new washing program.
Fill the detergent dispenser with detergent before you
set a new washing program.
4. Close the door.
– The countdown starts. The display shows re-
maining time to the start of the washing pro-
gram.
End of the washing program
The washing program is complete when:
• The display shows 0.
– When the countdown is completed, the washing
program starts automatically.
• The Finished indicator comes on.
1. Switch off the appliance.
2. Open the door.
With the delay start function set, the Washing in-
dicator light goes off. Once the countdown of the
delay start has ended, the washing program will start
automatically and the Washing indicator light comes
on.
– For better drying results, keep the door ajar for
some minutes before you remove the dishes.
Let the dishes cool down before you remove them from
the appliance. Hot dishes are easily damaged.
If you open the door during the countdown, this
will interrupt the countdown. When you close the
door again, the countdown continues from the point of
interruption.
Removing the load
• First remove items from the lower basket, then from
the upper basket.
11
• There can be water on the sides and door of the
appliance. Stainlesssteelbecomescoolmorequick-
ly than the dishes.
Care and cleaning
Warning! Switch the appliance off before you
clean it.
Cleaning the filters
Important! Do not use the appliance without the filters.
Make sure that the installation of the filters is correct.
Incorrect installation will cause unsatisfactory washing
results and damage to the appliance.
5
6
Put the filter A in the bot- Put the filter system in po-
tom of the appliance. In- sition. To lock the filter
stalltheflatfiltercorrectly system, turn the handle
under the two guides D. clockwise until it locks in
position
Important! Do not remove the spray arms.
If the holes in the spray arms become clogged, remove
remaining parts of soil with a cocktail stick.
1
2
Fully clean the filters A, B
and C below running wa-
ter.
External cleaning
Clean the external surfaces of the appliance and con-
trol panel with a damp soft cloth. Only use neutral de-
tergents. Do not use abrasive products, scouring pads
or solvents (acetone etc.).
Internal cleaning
Doaninspectionatintervals of3months. Setawashing
program for heavily soiled dishes. Use detergent, but
do not put dishes in the appliance.
3
4
Long periods of non-operation
Do these steps when you do not use the appliance for
a long period:
To remove filters B and Remove the flat filter A
C, turn the handle ap-
proximately 1/4 anti-
clockwise.
from the bottom of the ap-
pliance.
1. Disconnect the mains plug from the mains socket.
2. Close the water tap.
3. Keep the door open to prevent unpleasant smells.
4. Keep the inner side of the appliance clean.
Frost precautions
Caution! Do not install the appliance where the
temperature is below 0 °C. The manufacturer is
not responsible for damage because of frost.
12
If not possible, empty the appliance and close the door. 1. Disconnect the mains plug from the mains socket.
Disconnect the water inlet hose and remove water from
the water inlet hose.
2. Close the water tap.
3. Remove the appliance and the hoses.
4. Do not tilt the appliance during transport.
Moving the machine
Do these steps to move the appliance:
What to do if…
The appliance does not start or stops during operation.
If there is a fault, first try to find a solution to the problem
yourself. Refer to following charts. If you cannot find a
solution to the problem yourself, contact your dealer or
the Customer Care Centre.
Warning! Switch the appliance off before you do
the suggested corrective actions.
Fault code and malfunction
Possible cause and solution
•
• The water tap is blocked or restricted with limescale.
Clean the water tap.
the digital display shows
The appliance does not fill with water
• The water tap is closed.
Open the water tap.
• The filter in the water inlet hose is blocked.
Clean the filter.
• The installation of the water inlet hose is not correct. The hose
can be kinked or squashed.
Make sure that the installation is correct.
•
• There is a blockage in the sink spigot.
Clean the sink spigot.
the digital display shows
The appliance will not drain
• The installation of the water drain hose is not correct. The hose
can be kinked or squashed.
Make sure that the installation is correct.
•
• Close the water tap and contact your Customer Care Centre.
the digital display shows
The anti-flood device operates
The program does not start
• The appliance door is not closed.
Close the door.
• Mains plug is not connected.
Plug-in appliance to the mains.
• The fuse has blown out in the household fuse box.
Replace the fuse.
• Delay start is set.
Cancel the delay start to start the program immediately.
After the check, switch on the appliance. The program These data are necessary to help you quickly and cor-
continues from the point of interruption. If the malfunc- rectly:
tion shows again, contact your Customer Care Centre.
If the display shows a fault code, not described in the
chart, contact your Customer Care Centre.
• Model (Mod.)
• Product number (PNC)
• Serial number (S.N.)
13
For these data, refer to the rating plate.
Write the necessary data here:
Model description : ..........
Product number : ..........
Serial number : ..........
The cleaning results are not satisfactory
The dishes are not clean
• The selected washing program is not applicable for the type of load and
soil.
• The baskets are loaded incorrectly so that water cannot reach all surfaces.
• Spray arms do not turn freely because of incorrect arrangement of the
load.
• The filters are dirty or not correctly installed.
• The quantity of detergent is too little or missing.
The dishes are wet and dull
• No rinse aid has been used.
• The rinse aid dispenser is empty.
There are streaks, milky spots or • Decrease the rinse aid dosage.
a bluish coating on glasses and
dishes
Dry water drop stains on glasses • Increase rinse aid dosage.
and dishes
• The detergent can be the cause.
14
Technical data
Dimensions
Width (mm)
Height (mm)
Depth (mm)
596
850
610
Electrical connection - Voltage -
Overall power - Fuse
Information on the electrical connection is given on the rating plate on the
inner edge of the dishwasher door.
Water supply pressure
Minimum
50 kPa (7 psi)
800 kPa (116 psi)
12
Maximum
Capacity
Place settings
Environment concerns
The packaging materials are environmentally friendly
and can be recycled. The plastic components are iden-
tified by markings, e.g. >PE<, >PS<, etc. Discard the
packaging materials in the applicable container at the
community waste disposal facilities.
Old appliance
Make sure that the appliance goes to the applicable
collection point for recycling.
Make sure that this appliance is discarded correctly.
Inappropriate waste discard of the appliance causes
negative consequences for the environment and hu-
man health.
Warning! To discard the appliance, follow the
procedure:
For more information about the recycling of this appli-
ance, contact your local city office, your household
waste disposal service or the shop where you pur-
chased the appliance.
• Pull the mains plug out of the socket.
• Cut off the mains cable and mains plug and discard
them.
• Discard the door catch. This prevents children clos-
ing themselves inside the appliance and endanger-
ing their lives.
15
Installation
Fitting under a counter
Adjusting the level of the appliance
Make sure that the appliance is level to close and seal
the door correctly. If the level of the appliance is correct,
the door does not catch on the sides of the cabinet. If
the door does not close correctly, loosen or tighten the
adjustable feet until the appliance is level.
Warning! Make sure that mains plug is
disconnected from the mains socket during
installation.
Put the appliance adjacent to a water tap and a water
drain.
Adhesive steam protection foil
If the worktop is removed, fit the steam protection onto
the front part of the kitchen cabinet benchtop.
The plinth on freestanding appliance is not adjustable.
Do not remove the appliance worktop if you want to use
the dishwasher as a freestanding appliance.
Remove the appliance worktop to install it under a sink
unit or a kitchen worktop.
Make sure that the dimensions of the recess agree with
the given dimensions.
The steam protection foil is not supplied with free-
standing models, but can be purchased from
Electrolux Spare Parts.
1
3
2
4
Water connection
• If cold water pressure is in excess of 800 kPa, a
pressure reducing valve should be used. Check for
leaks.
Water inlet hose
Connect the appliance to a cold water supply.
Connect the inlet hose to a water tap with an external
BSP thread spout of 3/4”.
Caution! Always use new hoses when you
connect the appliance to the water mains. Old
hoses must not be used. The water inlet hose must be
examined at an interval of twelve months for
deterioration and replaced if necessary.
Inlet water supply
• Cold water pressure: 800 kPa max - 50 kPa min.
• Water flow rate 10 L / minute min.
16
The water pressure must be in the limits (refer to 'Tech- The appliance has a security feature to prevent dirty
nical data'). Make sure that the local water authority
gives you the average mains pressure in your area.
water going back into the appliance. If, the spigot of the
sink has a 'non-return valve', this valve can cause the
Make sure that there are no kinks in the water inlet hose appliance to drain incorrectly. Remove the non-return
and that the water inlet hose is not squashed or entan- valve.
gled.
Make sure that the water couplings are tight to prevent
water leakage.
Fit the hose nut correctly to prevent water leaks.
Caution! Do not connect the appliance to new
pipes or pipes that have been not used for a long
time. Let the water run for some minutes, then connect
the inlet hose.
Caution! Ensure that hoses are not crushed or
kinked under or behind the appliance.
Water drain hose
The highest point of the drain hose must be no more
than 60 cm from the floor and must have a continuous
fall.
The drain hose can be lengthened using additional
lengths and connectors. These must be purchased
from Electrolux Spare Parts. The extension length must
not exceed 2 metres.
The drain hose must be free of kinks and obstructions.
Remove the sink plug when the appliance drains the
water to prevent that the water goes back into the ap-
pliance.
Caution! Once connected the inlet hose to the
water tap, turn the tap on and check that there
are no leaks.
If you connect the water drain hose to a trap spigot
under the sink, remove the plastic membrane. If you do
not remove the membrane, remaining food can cause
a blockage in the drain hose spigot.
Electrical connection
Warning! Safetystandardsrequiretheappliance
to be earthed.
Prior to using the appliance for the first time, ensure
that the rated voltage and type of supply on the rating
plate match that of the supply where the appliance is
to be installed.
The fuse rating is also to be found on the rating plate.
17
Always plug the mains plug onto a correctly installed
approved socket.
Never unplug the appliance by pulling on the cable.
Always pull the plug.
Do not use multi-ways plugs, connectors and extension Test the appliance. Run a quick washing program and
cables. This can constitute a fire hazard through
overheating.
ensure that the appliance fills with water, washes and
drains with no leaks.
If necessary, have the domestic wiring system socket
The manufacturer accepts no liability for failure to
replaced. If the mains cable has to be replaced, contact observe the above safety precautions.
your local Customer Care centre.
The mains plug must be accessible after the appliance
has been installed.
18
Warranty
conditions, repair or replace any parts which it
considers to be defective. You agree that any re-
placed Appliances or parts become the property
of Electrolux. This warranty does not apply to light
globes, batteries, filters or similar perishable
parts.
FOR SALES IN AUSTRALIA AND NEW ZEALAND
This document sets out the terms and conditions
of product warranties for Electrolux branded ap-
pliances. It is an important document. Please keep
it with your proof of purchase documents in a safe
place for future reference should you require serv-
ice for your Electrolux appliance. General Terms
and Conditions
5. Parts and Appliances not supplied by Electrolux
are not covered by this warranty.
6. Where you are within an Electrolux service area,
this warranty covers the cost of transport of the
Appliance to and from Authorised Service Centres
of Electrolux and travelling costs for representa-
tives of the Authorised Service Centre to and from
your home or business. If you are outside an Elec-
trolux service area, you will bear these costs. For
information about whether you are within an Elec-
trolux service area, please phone 13 13 49 in
Australia, or 0800 10 66 10 in New Zealand.
1. In this warranty
– Electrolux' means Electrolux Home Products
Pty Ltd ABN 51 004 762 341 in respect of Ap-
pliances purchased in Australia and Electrolux
(NZ) Limited in respect of Appliances pur-
chased in New Zealand;
– 'Appliance' means any Electrolux product pur-
chased by you accompanied by this document;
7. Proofofpurchase isrequiredbeforeyoucan make
a claim under this warranty.
– 'Warranty Period' means
i) where you use the Appliance for personal,
domestic or household purposes in Australia
the period of 24 months and in New Zealand
the period of 24 months;
ii) where you use the Appliance for commercial
purposes, in Australia the period of 0 months
and in New Zealand the period of 0 months, (if
the period stated is 0 months you are not cov-
ered by this product warranty) following the
date of original purchase of the Appliance;
8. You may not make a claim under this warranty
unless the defect claimed is due to faulty or de-
fective parts or workmanship. Electrolux is not li-
able in the following situations (which are not ex-
haustive):
– The Appliance is damaged by
i) accident
ii) misuse or abuse, including failure to properly
maintain or service
iii) normal wear and tear
iv) power surges, electrical storm damage or
incorrect power supply
v) incomplete or improper installation
vi) incorrect, improper or inappropriate opera-
tion
– 'you' means the purchaser of the Appliance not
having purchased the appliance for re-sale,
and 'your' has a corresponding meaning.
2. This warranty only applies to Appliances pur-
chased and used in Australia or New Zealand and
is in addition to (and does not exclude, restrict, or
modify in any way) any non-excludable statutory
warranties in Australia or New Zealand.
vii) insect or vermin infestation.
– The Appliance is modified without authority
from Electrolux in writing.
3. Electrolux warrants that, when dispatched from an
Electrolux warehouse, the Appliance is free from
defects in materials and workmanship for the War-
ranty Period.
– The Appliance's serial number or warranty seal
has been removed or defaced.
– The Appliance was serviced or repaired by
anyone other than Electrolux or its Authorised
Service Centres.
4. During the Warranty Period Electrolux or its Au-
thorised Service Centre will, at no extra charge if
your appliance is readily accessible without spe-
cial equipment, and subject to these terms and
9. This warranty, the contract to which it relates and
the relationship between you and Electrolux are
19
governed by the law applicable in the Australian
State where the Appliance was purchased or the
law applicable in New Zealand if the Appliance
was purchased in New Zealand. Where the Ap-
pliance was purchased in New Zealand for busi-
nesspurposestheConsumer Guarantee Actdoes
not apply.
– in the case of Appliances, at its option, to the
replacement or repair of the Appliances or the
supply of equivalent products or the payment
ofthecostofreplacingtheAppliancesorhaving
the Appliances repaired or of acquiring equiv-
alent Appliances. Upon being replaced, parts
and Appliances become the property of Elec-
trolux; or
Limitation of Liability
10. To the extent permitted by law:
– in the case of services, at its option, to the sup-
ply of the services again or the payment of the
cost of having the services re-supplied;
and in the case of Appliances or services supplied
in New Zealand, loss or damage whether direct or
indirect or consequential that is reasonably fore-
seeable.
– Electrolux excludes all warranties other than as
contained in this document;
– Electrolux shall not be liable for any loss or
damage whether direct or indirect or conse-
quential arising from your purchase, use or
non-use of the Appliance.
Privacy
11. Provisions of the Trade Practices Act and State
consumer legislation in Australia, and the Con-
sumer Guarantees Act, the Sale of Goods Act and
the Fair Trading Act in New Zealand, imply war-
ranties or conditions, or impose obligations, upon
Electrolux which cannot be excluded, restricted or
modified. To the extent permitted by law, the lia-
bility of Electrolux (if any) arising out of or in rela-
tion to the Appliance or any services supplied by
Electrolux shall be limited (where it is fair and rea-
sonable to do so),:
You acknowledge that in the event that you make a
warranty claim it will be necessary for Electrolux and
its Authorised ServiceCentres toexchange information
in relation to you to enable Electrolux to meet its obli-
gations under this warranty.
Important Notice
Before Calling a Service Technician pleasecheck care-
fully the operating instructions, service booklet and the
warranty terms and conditions.
FOR SERVICE
SERVICE AUSTRALIA
FOR SPARE PARTS
OR TO FIND THE ADDRESS OF
YOUR NEAREST STATE SERV-
ICE CENTRE IN AUSTRALIA
Please call 13 13 4 9
OR TO FIND THE ADDRESS OF
YOUR NEAREST STATE SPARE
PARTS CENTRE IN AUSTRALIA
ELECTROLUX HOME PROD-
UCTS
Please call 13 13 50
For the cost of a local call (Australia only)
For the cost of a local call (Australia only)
FOR SERVICE
SERVICE NEW ZEALAND
FOR SPARE PARTS
OR TO FIND THE ADDRESS OF
YOUR NEAREST AUTHORISED
SERVICE CENTRE IN NEW ZEA-
LAND
OR TO FIND THE ADDRESS OF
YOUR NEAREST SPARE PARTS
CENTRE IN NEW ZEALAND
Free call 0800 10 66 20
ELECTROLUX HOME PROD-
UCTS
Free call 0800 10 66 10
(New Zealand only)
(New Zealand only)
20
21
22
23
|